0
TECHNICAL PAPERS

Experimental Identification of Dynamic Parameters of Rolling Element Bearings in Machine Tools

[+] Author and Article Information
D. M. Shamine, S. W. Hong, Y. C. Shin

School of Mechanical Engineering, Purdue University, West Lafayette, IN 47907

J. Dyn. Sys., Meas., Control 122(1), 95-101 (May 11, 1998) (7 pages) doi:10.1115/1.482432 History: Received May 11, 1998
Copyright © 2000 by ASME
Your Session has timed out. Please sign back in to continue.

References

Reddy,  W. R., and Sharan,  A. M., 1987, “The Finite Element Modeled Design of Lathe Spindles: The Static and Dynamic Analyses,” ASME J. Vibr. Acoust., Stress Reliab. Design, 109, pp. 417–415.
Al-Shareef,  K. J. H., and Brandon,  J. A., 1990, “On the Effects of the Variations in the Design Parameters on the Dynamic Performance of Machine Tools Spindle Bearing Systems,” Int. J. Machine Tools Manufact., 30, No. 3, pp. 432–445.
Wang,  W. R., and Chang,  C. N., 1994, “Dynamic Analysis and Design of a Machine Tool Spindle Bearing System,” ASME J. Vibr. Acoust., 116, pp. 280–285.
Brandon,  J. A., and Al-Shareef,  K. J. H., 1992, “Optimization Strategies for Machine Tool Spindle Bearing Systems: Critical Review,” ASME J. Eng. Ind., 114, pp. 244–253.
Yoshimura,  M., 1979, “Computer-Aided Design Improvement of Machine Tool Structure Incorporating Joint Dynamics Data,” Ann. CIRP, 28, pp. 241–246.
Wang,  K. W., Shin,  Y. C., and Chen,  C. H., 1992, “On the Natural Frequencies of High-Speed Spindles with Angular Contact Bearings,” Proceedings of Institutions of Mechanical Engineering, J. Mech. Eng. Sci., 205, pp. 147–154.
Shin,  Y. C., 1992, “Bearing Nonlinearity and Stability Analysis in High Speed Machining,” ASME J. Eng. Ind., 114, pp. 23–30.
Chen,  C. H., Wang,  K. W., and Shin,  Y. C., 1994, “An Integrated Approach Toward the Dynamic Analysis of High Speed Spindles, Part 1: System Model,” ASME J. Vibr. Acoust., 116, pp. 506–513.
Mottershead,  J. E., and Friswell,  M. I., 1993, “Model Updating in Structural Dynamics: A Survey,” J. Sound Vib., 167, No. 2, pp. 347–375.
Butner,  M. F., Murphy,  B. T., and Akian,  R. A., 1991, “The Influence of Mounting Compliance and Operating Conditions on the Radial Stiffness of Ball Bearings: Analytic and Test Results,” ASME Rotat. Machin. Vehicle Dynam., DE-Vol. 35, pp. 155–162.
Goodwin,  M. J., 1991, “Experimental Technique for Bearing Impedance Measurement,” ASME J. Eng. Ind., 113, pp. 335–342.
Hong,  S. W., and Lee,  C. W., 1991, “Identification of Linearized Joint Structural Parameters by Combined Use of Measured and Computed Frequency Responses,” Mech. Syst. Sig. Proc., 5, No. 4, pp. 267–277.
Wang,  J. H., and Horng,  S. B., 1994, “Investigation of the Tool Holder System with a Taper Angle 7:24,” Int. J. Machine Tools Manufact., 34, No. 8, pp. 1163–1176.
Ren,  Y., and Beards,  C. F., 1995, “Identification of Joint Properties of a Structure Using FRF Data,” J. Sound Vib., 186, No. 4, pp. 567–587.
Marsh,  E. R., and Yantek,  D. S., 1997, “Experimental Measurement of Precision Bearing Dynamic Stiffness,” J. Sound Vib., 202, No. 1, pp. 55–66.
Chen,  J. H., and Lee,  A. C., 1997, “Identification of Linearized Dynamic Characteristics of Rolling Element Bearings,” ASME J. Vibr. Acoust., 119, pp. 60–69.
Hong,  S. W., Shamine,  D. M., and Shin,  Y. C., 1999, “An Efficient Identification Method for Joint Parameters in Mechanical Structures,” ASME J. Vibr. Acoust., 121, No. 3, pp. 363–372.
Kim,  T. R., Wu,  S. M., and Ehmann,  K. F., 1989, “Identification of Joint Parameters for a Taper Joint,” ASME J. Eng. Ind., 111, pp. 282–287.
Jorgensen,  B. R., and Shin,  Y. C., 1997, “Dynamics of Machine Tool Spindle/Bearing Systems Under Thermal Growth,” ASME J. Tribol., 119, No. 4, pp. 875–882.
Jorgensen,  B. R., and Shin,  Y. C., 1998, “Dynamics of Spindle-Bearing Systems at High Speeds Including Cutting Load,” ASME J. Manuf. Sci. Eng., 120, No. 2, pp. 387–394.

Figures

Grahic Jump Location
Flowchart for the FRF-based identification scheme
Grahic Jump Location
Configuration of the high speed spindle with cutter and toolholder
Grahic Jump Location
Experiment 1: (a) index functions; (b) measured FRF at the rear end; (c) measured FRF at the front
Grahic Jump Location
Coherence functions in FRF measurement: (a) experiment 1, front; (b) experiment 1, rear; (c) experiment 4, front; (d) experiment 4, rear
Grahic Jump Location
Comparison of measured FRF’s and estimated FRF’s with transverse damping for experiment 2: (a) rear; (b) front
Grahic Jump Location
First three mode shapes of the horizontal mill spindle
Grahic Jump Location
Comparison of measured FRF’s and estimated FRF’s with transverse and tilting damping for experiment 2: (a) rear; (b) front
Grahic Jump Location
Comparison of measured FRF’s and estimated FRF’s with transverse and tilting damping for experiment 1: (a) rear; (b) front
Grahic Jump Location
Configuration of the MAZAK spindle with extension tool
Grahic Jump Location
MAZAK spindle experiment: (a) index functions; (b) measured FRF on the toolholder directly below the spindle; (c) measured FRF at the tip of the extension tool

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In