Research Papers

Resonance Tracking of Continua Using Self-Sensing Actuators

[+] Author and Article Information
Dominik Kern1

Chair for Engineering Mechanics (ITM),  Karlsruhe Institute of Technology (KIT), Karlsruhe 76131, Germanykern@kit.edu

Tobias Brack

Chair for Engineering Mechanics (ITM),  Karlsruhe Institute of Technology (KIT), Karlsruhe 76131, Germanybrack@imes.mavt.ethz.ch

Wolfgang Seemann

Chair for Engineering Mechanics (ITM),  Karlsruhe Institute of Technology (KIT), Karlsruhe 76131, Germanyseemann@kit.edu


Corresponding author.

J. Dyn. Sys., Meas., Control 134(5), 051004 (Jun 05, 2012) (9 pages) doi:10.1115/1.4006224 History: Received April 28, 2011; Revised February 06, 2012; Published June 05, 2012; Online June 05, 2012

This paper proposes and develops an innovative method to solve the resonance tracking problem for actuator and sensor applications to obtain maximum power transmission or signal selectivity using a modified phase-locked loop (PLL). The tracking of a higher eigenfrequency is very useful in some cases, but it is more challenging than the excitation of the only eigenfrequency of a 1-DoF system. The resonances are identified through employing their characteristic phase difference. The conventional PLL was modified to track a certain phase difference without deviation. The closed loop is a nonlinear control system due to the conversion between harmonic signals and phase signals. However, a model simplification to linear elements allows the goal oriented determination of the controller parameters. The advantages of self-sensing in combination with resonance tracking are attractive for practical applications such as ultrasonic motors and compact force sensors. The conducted experiments approved the effectiveness of the resonant excitation of higher oscillation modes of continua using self-sensing actuators.

Copyright © 2012 by American Society of Mechanical Engineers
Your Session has timed out. Please sign back in to continue.



Grahic Jump Location
Figure 6

Root-locus plot of the modified PLL without mechanical system as function of KP for three values of TN  = KP /KI , the root loci of the chosen parameters are marked (crosses)

Grahic Jump Location
Figure 1

A prestressed, clamped–clamped beam with piezoelectric transducers (MFC type) on both sides of the middle section (l1  < x < l2 )

Grahic Jump Location
Figure 2

FRF for the unstressed and with Fv  = 100 N prestressed beam

Grahic Jump Location
Figure 3

Bridge circuit for self-sensing assuming the electrically equivalent model of the piezoelectric material [19]

Grahic Jump Location
Figure 4

Structure of the conventional PLL [23]

Grahic Jump Location
Figure 5

Linear (solid line boxes) and nonlinear elements (dashed line boxes) in the closed-loop

Grahic Jump Location
Figure 7

The basin of attraction around the resonance frequencies (red dot) is bounded by the neighboring antiresonance frequencies (blue asterisk)

Grahic Jump Location
Figure 8

Transient responses of the simplified model tracking a frequency step and the full model tracking a step of the beam’s eigenfrequency

Grahic Jump Location
Figure 9

Photograph of the experimental setup

Grahic Jump Location
Figure 10

Signal flow scheme of the self-sensing experiments

Grahic Jump Location
Figure 11

FRF using self-sensing for the unstressed and with Fv  = 200 N prestressed beam

Grahic Jump Location
Figure 12

Tracking the second eigenfrequency in conventional mode (no self-sensing) for different controller parameters

Grahic Jump Location
Figure 13

Tracking the fourth eigenfrequency with self-sensing in the experiment: (a) continuously increasing the prestress; (b) step changes of the prestress (step up at t = 4 s, step down at t = 5.25 s)



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In